年度归档：2024

Rotary lobe blower roots

• Roots blower is a volumetric fan, with impeller end face and front and rear end covers of the fan.
• The principle is a rotary compressor that uses two blade-shaped rotors to move relative to each other in the cylinder to compress and transport gas.
• This type of blower has a simple structure and is easy to manufacture. It is widely used in aquaculture oxygenation, sewage treatment aeration, cement transportation, and is more suitable for gas transportation and pressurization systems in low-pressure situations. It can also be used as a vacuum pump.

rotary lobe blower roots

Roots rotary lobe blower manual

• How to use
• Usage requirements:
  (1) The inlet air temperature is not greater than 40°C
  (2) The content of solid particles in the gas shall not be greater than 100 mg/m2, and the largest particle shall not be greater than half of the assembly gap;
  (3) The bearing temperature does not exceed 95°C;
  (4) The lubricating oil temperature does not exceed 65°C;
  (5) The opening pressure range specified on the sign shall not be exceeded.
• Preparations before startup:
  (1) Check the installation quality of each fastener and positioning pin;
  (2) Check the installation quality of intake and exhaust pipes and valves;
  (3) Check whether the base of the unit is fully padded and whether the anchor bolts are tightened;
  (4) Inject the specified brand of lubricating oil into the gear box to the driving side of the oil mark position and inject the specified grease in sufficient quantity;
  (5) Open all the blower inlet and exhaust valves, turn the rotor, and listen carefully for any abnormal noises from various parts;
  (6) For fans with water cooling requirements, the water temperature should not be higher than 25°C.
• No-load test operation of the fan:
  (1) Newly installed or overhauled fans should undergo no-load test operation;
  (2) No-load operation means putting into operation with the intake and exhaust valves fully open;
  (3) There is no abnormal smell, smoke, collision or friction sound, and the radial vibration of the bearing part is not greater than 6.3mm/s;
  (4) Run with no load for about 30 minutes. If the situation is normal, it can be put into operation with load. If abnormal operation is found, stop the machine immediately for inspection. After troubleshooting, it still needs to run with no load.
• Continuous operation under normal load:
  (1) It is required to gradually and slowly increase the voltage and bring the load up to the rated load. It is not allowed to adjust to the rated load at one time;
  (2) During normal operation of the fan, it is strictly prohibited to completely close the engine and exhaust valves; nor is it allowed to operate overloaded;
  (3) Due to the characteristics of the fan, it is not allowed to directly backflow the exhaust gas for a long time, so cooling measures must be taken;
  (4) The blower should not stop suddenly under full load to avoid damage to parts.
• Maintenance and overhaul:
  (1) Check the fastening of each part and whether the positioning pin is loose;
  (2) Check the machine body frequently for oil leakage;
  (3) Pay attention to whether the lubrication is normal, pay attention to the amount of lubricating grease, always listen to the operation of the fan to see if there is any noise, and pay attention to whether the unit is operating under specified working conditions;
  (4) Lubricating oil (grease): The lubricating oil is medium-load industrial gear oil (grade 220, kinematic viscosity 198~242mm2/s40℃, flash point ≥200℃); the grease is butter (synthetic lithium-based grease penetration 220250 , dropping point ≥190℃), after 200 hours of operation, the oil and grease must be changed for the first time, and for the second time after one month of operation. In the future, it should be replaced according to the usage environment and oil (grease) quality. It is recommended to replace it every three months;
  (5) Check the air inlet gas filter frequently and clean or replace the filter in time;
  (6) The overload of the blower is sometimes not displayed immediately, so pay attention to the increase trend of the inlet and exhaust pressure, bearing temperature and motor current to judge whether the fan is operating normally;
  (7) Before disassembling the machine, the dimensions of the machine should be measured, recorded, and marked on the parts to ensure that the original coordination requirements are maintained after assembly;
  (8) After a new machine or overhaul, the fuel tank should be cleaned and put into operation according to the usage procedures. It is recommended to replace all lubricating grease after 8 hours of operation.

rotary lobe blower roots

Roots blower manufacturers

• Since its establishment in the early 1990s, Longgu Heavy Industry has become a diversified machinery enterprise integrating fan and pneumatic conveying equipment system engineering.
• Our company has advanced computer-aided design and manufacturing, CNC machining technology, and adopts information technologies such as computer-aided design and CAPPCT to improve product design and manufacturing accuracy and shorten the design and manufacturing cycle.
• Shandong Longgu Heavy Industry Machinery Co., Ltd. has imported advanced and high-precision machining equipment from many countries, including fully automatic machining centers, CNC boring and milling machines, and dynamic balancing instruments. It has a high-level, large-scale, and modern mechanical processing and manufacturing workshop.
• The company has completed the implementation and control of its internal quality management system, achieving independent quality control of products from research and development design to finished product delivery. It has established and improved a full process self-control system from design and production to quality, installation, and service, providing sufficient basis and reliable guarantee for the stability and durability of products.
• We have cooperated with higher education institutions such as Shandong University, Shandong University of Technology, and Southwest University of Technology to strengthen the research and development of key core technologies. We have overcome technical difficulties and developed new products such as diesel engine driven Roots blowers, water-cooled dual tank Roots blowers, and low-noise Roots blowers, filling multiple industry gaps.
• At present, our company's main products include LGSR three leaf Roots blower, LGSR-V Roots vacuum pump, LGSR-H high-pressure blower series, bipolar series high-pressure, gas pressurized explosion-proof, pneumatic conveying series fans, steam compressors, LGMJ dense series fans, rotary fans, centrifugal fans, etc.
• Our company's products are widely used in industries such as sewage treatment, pneumatic conveying, vacuum packaging, grain processing, electricity, petrochemicals, cement, mining, and special gas pressurized conveying.
• We have close cooperative relationships with top domestic enterprises such as Sande Group, COFCO Group, and Shanshui Cement. Our company's sales outlets and after-sales service centers are located throughout the country and exported to countries such as Malaysia, India, Kyrgyzstan, Nigeria, etc.

Roots blower uses

• ‌Roots blowers‌ are widely used in many industries and fields, mainly including:
• ‌Sewage treatment‌: In the sewage treatment industry, roots style blowers are widely used in aeration, stirring, mixing and other aspects to ensure the smooth progress of the sewage treatment process.
• ‌Pneumatic conveying system‌: roots style blowers are used to transport feed, lime powder, monosodium glutamate, soybean skin, silica and other powdery materials, as well as grain suction machines or crane suction vacuum pumps in grain transportation to ensure the effectiveness of materials transmission.
• ‌Aquaculture‌: In aquaculture, roots style blowers use micropore aeration technology to oxygenate water quality and improve breeding efficiency.They are important equipment in the aquaculture industry.
• ‌Coal chemical industry‌: In the coal chemical industry, Roots blowers are used in sewage treatment and different processes, playing an important role in improving production efficiency and product quality‌.
• ‌Dust removal industry‌: Roots blowers are also used in the dust removal industry, such as desulfurization, denitrification, dust removal, etc., to ensure the effective treatment of industrial flue gas and waste gas.
• ‌Grain processing, flour mills, food factories‌: used in transportation, drying, cooling, dust and other links to ensure the smooth progress of the food processing process‌.
• ‌Paint and Coating Industry‌: Used for ventilation, dust removal and waste gas treatment to ensure the safety and health of the working environment.
• ‌Mining, quarrying, and mineral processing industries‌: used in emissions, exhaust, gas transportation, drying and other links to ensure environmental control and safety during the development of mineral resources‌.
• ‌Pharmaceutical Industry‌: In the pharmaceutical industry, Roots blowers are used in pharmaceutical processing, chemical reactions and other aspects, such as laboratory ventilation equipment, to ensure the safety and efficiency of the pharmaceutical production process‌.

What is a root blower

• Roots blower is a volumetric blower, also called a rotary blower, which is mainly used to transport gas. ‌It compresses and transports gas through relative movement of two blade-shaped rotors in the cylinder, and is a type of rotary compressor.
• Roots blowers have a simple structure and are easy to manufacture. They are widely used in various industrial fields, such as aquaculture oxygenation, sewage treatment aeration, cement transportation, etc. It is particularly suitable for gas delivery and pressurization systems in low-pressure situations, and can also be used as a vacuum pump.
• The principle of Roots blower is to use two blade-shaped rotors to make relative motion in the cylinder to compress and transport gas.
• This design makes the Roots blower have the characteristics of forced air transmission, and the air volume it delivers is proportional to the number of revolutions.
• There is a slight gap between the impeller end face of the Roots blower and the front and rear end covers of the fan.
• Driven by the synchronization gear, the gas is transported from the air inlet along the inner wall of the casing to the discharge side. This design makes the Roots blower relatively simple to operate and easy to maintain.

what is a root blower

Root blower working principle

• The working principle of Roots blower can be simply summarized into the following steps:
• 1.Suction stage: When the rotor rotates, the volume of the chamber gradually increases, forming a low-pressure area.This low-pressure area attracts outside air into the chamber.
• 2.Compression stage: As the rotor continues to rotate, the volume of the chamber gradually decreases.This process causes the air to become compressed, increasing its pressure.
• 3.Exhaust stage: When the volume of the chamber reaches the minimum value, the compressed air will be discharged from the chamber.At this time, the rotation of the rotor will increase the volume of the chamber again to prepare for the next round of suction.
• By repeating the above steps, the Roots blower can continuously suck in, compress and discharge air.This working principle enables Roots blowers to produce high-pressure, high-flow airflow.

Roots blower diagram

Roots blower uses

• ‌Roots blowers‌ are widely used in many industries and fields, mainly including:
• ‌Sewage treatment‌: In the sewage treatment industry, roots style blowers are widely used in aeration, stirring, mixing and other aspects to ensure the smooth progress of the sewage treatment process.
• ‌Pneumatic conveying system‌: roots style blowers are used to transport feed, lime powder, monosodium glutamate, soybean skin, silica and other powdery materials, as well as grain suction machines or crane suction vacuum pumps in grain transportation to ensure the effectiveness of materials transmission.
• ‌Aquaculture‌: In aquaculture, roots style blowers use micropore aeration technology to oxygenate water quality and improve breeding efficiency.They are important equipment in the aquaculture industry.
• ‌Coal chemical industry‌: In the coal chemical industry, Roots blowers are used in sewage treatment and different processes, playing an important role in improving production efficiency and product quality‌.
• ‌Dust removal industry‌: Roots blowers are also used in the dust removal industry, such as desulfurization, denitrification, dust removal, etc., to ensure the effective treatment of industrial flue gas and waste gas.
• ‌Grain processing, flour mills, food factories‌: used in transportation, drying, cooling, dust and other links to ensure the smooth progress of the food processing process‌.
• ‌Paint and Coating Industry‌: Used for ventilation, dust removal and waste gas treatment to ensure the safety and health of the working environment.
• ‌Mining, quarrying, and mineral processing industries‌: used in emissions, exhaust, gas transportation, drying and other links to ensure environmental control and safety during the development of mineral resources‌.
• ‌Pharmaceutical Industry‌: In the pharmaceutical industry, Roots blowers are used in pharmaceutical processing, chemical reactions and other aspects, such as laboratory ventilation equipment, to ensure the safety and efficiency of the pharmaceutical production process‌.

Roots blower specifications

Best roots blower repair near me

• Roots blower maintenance tips and precautions:
• Troubleshooting and preparation
• 1.Determine the cause of the fault: Before performing maintenance, you must first identify the specific fault symptoms of the blower, such as abnormal noise, increased vibration, reduced air volume, etc.
• 2.Power-off safety measures: Be sure to cut off the power supply before starting maintenance to ensure the safety of operators.
• Disassembly and cleaning
• 1.Disassembly steps: Disassemble the blower in the correct order to avoid damaging components.
• 2.Thorough cleaning: Use appropriate tools and solvents to remove dirt and sediment from the impeller, casing, etc.
• Replace damaged parts
• 1.Check worn parts: Check the wear of key components such as impellers, gears, and bearings.
• 2.Replace necessary parts: If there is any damage or serious wear, replace it with new original parts in time.
• Lubrication and adjustment
• 1.Check the lubricating oil: Confirm whether the lubricating oil needs to be replaced and whether the oil level is appropriate.
• 2.Adjust the gap: Adjust the gap between the impeller and the casing, and between the impeller and the impeller to the specified value to prevent internal leakage.
• Installation and testing
• 1.Reassembly: Reassemble the blower in the correct order.
• 2.Start-up test: After ensuring that everything is normal, conduct a no-load start-up test and observe the operating status.
• Daily maintenance points
• 1.Regular inspection: including whether the fasteners are loose, whether there is oil leakage, and whether there is scaling or corrosion inside.
• 2.Monitor operating parameters: such as intake and exhaust pressure, bearing temperature, current changes, etc.
• 3.Pay attention to abnormal sounds: monitor whether there are abnormal noises during operation.
• 4.Add grease regularly: Make sure bearings and other moving parts are fully lubricated.

roots blower repair near me

How much does it cost to rebuild a roots blower?

• Many people want to know how much a Roots blower costs. This article will introduce it to you in detail.
• First, you need to understand the classification of Roots blowers.
• Roots blowers can be divided into general-purpose and special-purpose types according to their uses, and can be divided into motor-driven and diesel-driven types according to their driving methods.
• Therefore, the prices of different types of Roots blowers are also different.
• The price of a universal Roots blower generally ranges from US$700 to US$3,000, depending on air volume, pressure, power and other parameters.
• Special-purpose Roots blowers are more expensive, generally above US$15,000, because they need to be customized according to customer needs, have a long production cycle, and have high technical requirements.
• There is also a difference in price between motor-driven and diesel-driven Roots blowers.
• The price of motor-driven models is relatively low, generally around $3,000.
• The diesel engine-driven model is more expensive, and the price of a Roots blower may reach more than 15,000 US dollars.
• In addition to the price differences between different types and drive methods, factors such as product quality and quality must also be considered.
• The price of high-end Roots blowers is generally more expensive than ordinary ones, but the quality and service are also more reliable.
• When purchasing a Roots blower, in addition to price factors, you must also consider whether the performance parameters of the equipment meet production needs, such as air volume, pressure, power, noise, etc.
• In addition, attention should also be paid to equipment maintenance and after-sales service.
• In summary, the price of Roots blowers varies depending on factors such as type, driving method, quality, etc. The price of a general-purpose motor-driven type is generally between US$700 and US$3,000, while the price of a dedicated diesel-driven type may reach US$15,000. USD and above.
• When purchasing, you need to make a selection based on production needs and equipment performance parameters, while paying attention to equipment maintenance and after-sales service.

roots blower repair near me

Who makes the best roots blower?

• Since its establishment in the early 1990s, Longgu Heavy Industry has become a diversified machinery enterprise integrating fan and pneumatic conveying equipment system engineering. Our company has advanced computer-aided design and manufacturing, CNC machining technology, and adopts information technologies such as computer-aided design and CAPPCT to improve product design and manufacturing accuracy and shorten the design and manufacturing cycle.
• Shandong Longgu Heavy Industry Machinery Co., Ltd. has imported advanced and high-precision machining equipment from many countries, including fully automatic machining centers, CNC boring and milling machines, and dynamic balancing instruments. It has a high-level, large-scale, and modern mechanical processing and manufacturing workshop.
• The company has completed the implementation and control of its internal quality management system, achieving independent quality control of products from research and development design to finished product delivery. It has established and improved a full process self-control system from design and production to quality, installation, and service, providing sufficient basis and reliable guarantee for the stability and durability of products.
• We have cooperated with higher education institutions such as Shandong University, Shandong University of Technology, and Southwest University of Technology to strengthen the research and development of key core technologies. We have overcome technical difficulties and developed new products such as diesel engine driven Roots blowers, water-cooled dual tank Roots blowers, and low-noise Roots blowers, filling multiple industry gaps.
• At present, our company's main products include LGSR three leaf Roots blower, LGSR-V Roots vacuum pump, LGSR-H high-pressure blower series, bipolar series high-pressure, gas pressurized explosion-proof, pneumatic conveying series fans, steam compressors, LGMJ dense series fans, rotary fans, centrifugal fans, etc.
• Our company's products are widely used in industries such as sewage treatment, pneumatic conveying, vacuum packaging, grain processing, electricity, petrochemicals, cement, mining, and special gas pressurized conveying.
• We have close cooperative relationships with top domestic enterprises such as Sande Group, COFCO Group, and Shanshui Cement. Our company's sales outlets and after-sales service centers are located throughout the country and exported to countries such as Malaysia, India, Kyrgyzstan, Nigeria, etc.

Roots dresser blower

Roots blower is a volumetric blower with impeller end face and front and rear end covers of the fan. The principle is a rotary compressor that uses two blade-shaped rotors to move relative to each other in the cylinder to compress and transport gas. This type of blower has a simple structure and is easy to manufacture. It is widely used in aquaculture oxygenation, sewage treatment aeration, cement transportation, and is more suitable for gas transportation and pressurization systems in low-pressure situations. It can also be used as a vacuum pump.

Roots blower working principle

Roots blower is a type of positive displacement fan. It has two three-bladed impellers that rotate relatively in a space sealed by the casing and wall panels. Since each impeller adopts an involute or epicycloid envelope Line, the three blades of each impeller are exactly the same, and the two impellers are also exactly the same, which greatly reduces the difficulty of processing. The impeller is processed using CNC equipment, which ensures that when the center distance between the two impellers remains unchanged, no matter where the two impellers rotate, a certain minimum gap can be maintained, thereby ensuring that gas leakage is within the allowable range.

Roots dresser blower diagram

Roots dresser blower uses

• ‌Roots blowers‌ are widely used in many industries and fields, mainly including:
• ‌Sewage treatment‌: In the sewage treatment industry, roots style blowers are widely used in aeration, stirring, mixing and other aspects to ensure the smooth progress of the sewage treatment process.
• ‌Pneumatic conveying system‌: roots style blowers are used to transport feed, lime powder, monosodium glutamate, soybean skin, silica and other powdery materials, as well as grain suction machines or crane suction vacuum pumps in grain transportation to ensure the effectiveness of materials transmission.
• ‌Aquaculture‌: In aquaculture, roots style blowers use micropore aeration technology to oxygenate water quality and improve breeding efficiency.They are important equipment in the aquaculture industry.
• ‌Coal chemical industry‌: In the coal chemical industry, Roots blowers are used in sewage treatment and different processes, playing an important role in improving production efficiency and product quality‌.
• ‌Dust removal industry‌: Roots blowers are also used in the dust removal industry, such as desulfurization, denitrification, dust removal, etc., to ensure the effective treatment of industrial flue gas and waste gas.
• ‌Grain processing, flour mills, food factories‌: used in transportation, drying, cooling, dust and other links to ensure the smooth progress of the food processing process‌.
• ‌Paint and Coating Industry‌: Used for ventilation, dust removal and waste gas treatment to ensure the safety and health of the working environment.
• ‌Mining, quarrying, and mineral processing industries‌: used in emissions, exhaust, gas transportation, drying and other links to ensure environmental control and safety during the development of mineral resources‌.
• ‌Pharmaceutical Industry‌: In the pharmaceutical industry, Roots blowers are used in pharmaceutical processing, chemical reactions and other aspects, such as laboratory ventilation equipment, to ensure the safety and efficiency of the pharmaceutical production process‌.

What is the difference between a Roots blower and a blower?

• Roots blowers and blowers both belong to the category of centrifugal fans, but they are very different in structure and working principle:
• Structural differences
  The unique structure of the Roots blower is composed of an outer rotor and an inner rotor. The two rotors mesh with each other to produce the effect of gas compression and transportation. This structure has the advantages of small size, low noise, no vibration and no oil pollution.
  The blower generates airflow through the rotation of the impeller in the casing, and then compresses and transports the airflow through the action of the air guide assembly. The blower has the advantages of compact structure, low energy consumption and long service life.
• Differences in working principles
  Roots blower generates gas compression and transportation effects in the casing through the mutual meshing of two rotors. Roots blowers usually rotate at very high speeds, so they require specialized care and maintenance when working.
  The blower generates airflow through the rotation of the impeller, and then compresses and transports the airflow through the cooperation of the guide components. The working speed of the blower is usually low and the operation is simple, so you need to pay attention to correct operation and maintenance during use.

What are the benefits of a Roots blower?

• High efficiency: Due to its internal sealing structure, the Roots blower can avoid gas leakage while transporting air flow, thereby achieving efficient and stable gas transport. Moreover, its operation efficiency is high and it can save certain costs in terms of energy consumption.
• Low noise: Compared with other types of blowers, Roots blowers have very low noise. This is due to the special noise elimination technology used in its design, which can ensure that the noise during operation is controlled within a reasonable range. It is especially suitable for Noise-sensitive work environment.
• Large displacement: Roots blowers can provide a large amount of gas transportation capacity. In the industrial production process, a large amount of gas is often needed to drive production equipment. At this time, Roots blowers can take advantage of their large displacement characteristics, thus better to meet the needs of the production process.
• Wear resistance: The internal structure of the Roots blower is reasonably designed, and there will be no friction or collision between the master rotor and the slave rotor, thereby avoiding wear and tear of machine parts. At the same time, in terms of manufacturing process, wear-resistant and corrosion-resistant materials are used to ensure the long-term use of the machine.
• Strong adaptability: Roots blowers can adapt to different working conditions such as various gases, pressures, flows, etc. Roots blowers can adapt to the different media such as high pressure, high temperature, corrosion, viscosity, etc. that are often encountered in industrial production. able to meet needs.

Who makes the best roots dresser blower?

• Since its establishment in the early 1990s, Longgu Heavy Industry has become a diversified machinery enterprise integrating fan and pneumatic conveying equipment system engineering. Our company has advanced computer-aided design and manufacturing, CNC machining technology, and adopts information technologies such as computer-aided design and CAPPCT to improve product design and manufacturing accuracy and shorten the design and manufacturing cycle.
• Shandong Longgu Heavy Industry Machinery Co., Ltd. has imported advanced and high-precision machining equipment from many countries, including fully automatic machining centers, CNC boring and milling machines, and dynamic balancing instruments. It has a high-level, large-scale, and modern mechanical processing and manufacturing workshop.
• The company has completed the implementation and control of its internal quality management system, achieving independent quality control of products from research and development design to finished product delivery. It has established and improved a full process self-control system from design and production to quality, installation, and service, providing sufficient basis and reliable guarantee for the stability and durability of products.
• We have cooperated with higher education institutions such as Shandong University, Shandong University of Technology, and Southwest University of Technology to strengthen the research and development of key core technologies. We have overcome technical difficulties and developed new products such as diesel engine driven Roots blowers, water-cooled dual tank Roots blowers, and low-noise Roots blowers, filling multiple industry gaps.
• At present, our company's main products include LGSR three leaf Roots blower, LGSR-V Roots vacuum pump, LGSR-H high-pressure blower series, bipolar series high-pressure, gas pressurized explosion-proof, pneumatic conveying series fans, steam compressors, LGMJ dense series fans, rotary fans, centrifugal fans, etc.
• Our company's products are widely used in industries such as sewage treatment, pneumatic conveying, vacuum packaging, grain processing, electricity, petrochemicals, cement, mining, and special gas pressurized conveying.
• We have close cooperative relationships with top domestic enterprises such as Sande Group, COFCO Group, and Shanshui Cement. Our company's sales outlets and after-sales service centers are located throughout the country and exported to countries such as Malaysia, India, Kyrgyzstan, Nigeria, etc.

Roots rotary lobe blower​

Roots blower is a volumetric fan, with impeller end face and front and rear end covers of the fan. The principle is a rotary compressor that uses two blade-shaped rotors to move relative to each other in the cylinder to compress and transport gas. This type of blower has a simple structure and is easy to manufacture. It is widely used in aquaculture oxygenation, sewage treatment aeration, cement transportation, and is more suitable for gas transportation and pressurization systems in low-pressure situations. It can also be used as a vacuum pump.

roots rotary lobe blower​

Roots rotary lobe blower manual

• 1.Usage requirements:
• (1) The inlet air temperature is not greater than 40°C
• (2) The content of solid particles in the gas shall not be greater than 100 mg/m2, and the largest particle shall not be greater than half of the assembly gap;
• (3) The bearing temperature does not exceed 95°C;
• (4) The lubricating oil temperature does not exceed 65°C;
• (5) The opening pressure range specified on the sign shall not be exceeded.
• 2.Preparations before startup:
• (1) Check the installation quality of each fastener and positioning pin;
• (2) Check the installation quality of intake and exhaust pipes and valves;
• (3) Check whether the base of the unit is fully padded and whether the anchor bolts are tightened;
• (4) Inject the specified brand of lubricating oil into the gear box to the driving side of the oil mark position and inject the specified grease in sufficient quantity;
• (5) Open all the blower inlet and exhaust valves, turn the rotor, and listen carefully for any abnormal noises from various parts;
• (6) For fans with water cooling requirements, the water temperature should not be higher than 25°C.
• 3.No-load test operation of the fan:
• (1) Newly installed or overhauled fans should undergo no-load test operation;
• (2) No-load operation means putting into operation with the intake and exhaust valves fully open;
• (3) There is no abnormal smell, smoke, collision or friction sound, and the radial vibration of the bearing part is not greater than 6.3mm/s;
• (4) Run with no load for about 30 minutes. If the situation is normal, it can be put into operation with load. If abnormal operation is found, stop the machine immediately for inspection. After troubleshooting, it still needs to run with no load.
• 4.Continuous operation under normal load:
• (1) It is required to gradually and slowly increase the voltage and bring the load up to the rated load. It is not allowed to adjust to the rated load at one time;
• (2) During normal operation of the fan, it is strictly prohibited to completely close the engine and exhaust valves; nor is it allowed to operate overloaded;
• (3) Due to the characteristics of the fan, it is not allowed to directly backflow the exhaust gas for a long time, so cooling measures must be taken;
• (4) The blower should not stop suddenly under full load to avoid damage to parts.

What are roots blowers used for?

• 1.Used for ventilation: Roots blowers can quickly transport gas from one area to another. Indoor ventilation is relatively common, so that good air quality and a comfortable working environment can be maintained. .
• 2.Used for waste gas emission: In some industrial processes, a large amount of waste gas will be produced, which needs to be discharged, otherwise it will cause environmental pollution. The Roots blower can quickly discharge these waste gases to ensure the safety of the production process.
• 3.Used for pressurized transportation: In some industrial fields, such as water treatment, paper manufacturing, power generation, etc., compressed air needs to be transported to drive equipment and production processes. Roots blowers can compress gas and transport it to the required area.
• 4.Use in other fields: Roots blowers can also be used in sewage treatment, dust collection, paint spraying, food processing, equipment and other fields, and their value is relatively wide.